Wednesday, January 14, 2015

PCB for Stratasys Cartridges

There's a *very* long list of things that I have yet to update on the blog, but this is something I'm going to stay on top of.

I recently found out from the Have Blue website that there is a way to flash the EEPROMS from scratch with a Raspberry Pi for the Stratasys 3d printer cartridges on the Dimension BST series printers. This means that you can refill the printer with 3rd party filament without modifying the printer, something that is going to become very useful since Stratasys is dropping support for the BST 1200 series on June 30th, 2015. I had already modified the 3d printer at my school in order to make student printing affordable, but this method requires the printer to be reset after reloading the cartridge EEPROM, which is a problem if a cartridge runs out during a print and all of the chips are empty.

After seeing all of this I thought that while people who already had EEPROMs from used cartridges would still be able to use the printers, those who had returned their used cartridges for a discount wouldn't be able to use this workaround without paying through the nose for a used cartridge, which would only continue to become more expensive and scarce. So I went to a friend of mine who is a whiz at making PCBs and asked if he could make a board for the EEPROMs that could substitute the originals. Since the circuit is only two pieces and the layout is straightforward he was able to make it in less than an hour in Eagle. Using OSH Park to make the boards gets you three PCBs for $6.65 (while the screenshot below makes it appear that the notch in the middle is missing it is present in the board outline). A suitable 4.7k ohm resistor can easily be found on DigiKey.

However, the original Maxim DS2433 EEPROM chip has been replaced with the DS24B33. The previous link contains details about the differences between the chips. Of particular note is the increased max current draw from 500 micro amps to 2 milliamps and the increase in recovery time. This may make the chip unusable with the Stratasys printers. DigiKey does have the DS24B33 available if you would like to try this chip. I will order one and will post results when I have them. It is also possible that if the new chip does not work out of the box there is a config file for the 1-wire interface on the Stratasys that could be edited to make it compatible.

The Eagle board and schematic files can be downloaded here. Note that these files may not be used for commercial sale and all use is AT YOUR OWN RISK. While the boards have been ordered from OSH Park and the schematic is very simple this board has not been tested and verified as of 1/14/2015.

Update 5/11/2015:
It has been a while since I've had time to work on this project. The PCBs came in the mail, and I've stuffed the boards with the parts. Unfortunately I wasn't able to communicate with the new chip using the bus pirate, although I'm not sure if this is because of a hardware problem or because the script I was using had an error trying to read a cartridge from a blank chip. Here is a side by side comparison between the original PCB (green) and the replacement (purple):


  1. hello Sir,
    I desperately need to know what tools and softwares needed to read/write/erase such chip.
    I have PIC Programmer K128 and Arduino Mega.
    would you please help at any suggestion.
    thanks and B.R

  2. Good cartridges are a lot littler than toner cartridges and work an alternate innovation. Good cartridges enable higher quality pictures to be delivered than toner cartridges for a lower unit cost.Multipack 10 cartucce Epson


  3. Incredible story there. What gsopoker happened after? Thanks! The Gaming Club bears a license from the direction of Gibraltar, and claims to be one of a choose few casinos that have a license from the Gibraltar government. A member of the Interactive Gaming Council (IGC), The Gaming Club follows all the guidelines laid next to by the organization, something that has later than a long way in it living thing qualified as a good place to gamble online.

    Everything virtually The Gaming Club feels good; be it the promotions, the huge number of games, the multiple banking options upon offer, the highly developed security measures, or the fair and liable gaming practices the casino adopts.

    The Gaming Club motors along upon software developed by one of the giants of online gaming software loan Microgaming. The software it uses is open-minded and has a range of features intended to affix your online gambling experience and make you desire to come support after every round of gambling you get here.

    Another hallmark of a fine casino is the character of its customer withhold team, and The Gaming Club does not disappoint on this front.